Amprobe VPC-10A Voltage and Continuity Tester

Amprobe VPC-10A Voltage and Continuity Tester 1

Amprobe VPC-10A Voltage and Continuity Tester 2

Amprobe VPC-10A Voltage and Continuity Tester

• Quickly troubleshoot voltage and continuity and detect presence of voltages easily
• Turns on when a complete circuit is sensed, automatically selects AC or DC voltage or continuity mode, and autos-off when removed from a circuit
• Seven visual voltage indicators clearly differentiating between key voltage levels

SKU: 4375914 Category: Voltage & Continuity

Description

Amprobe’s hand-held residential and commercial Voltage and Continuity Testers are loaded with safety, time-saving and accuracy features. They allow you to quickly troubleshoot voltage and continuity for residential and commercial applications using visual and audible alerts.

Quickly measure AC and DC voltage in circuitry and its components—including outlets, light fixtures, batteries and extension cords— as well as test the continuity of fuses, light bulbs and electrical connections.

In addition to full range polarity detection, they both signal continuity and voltage with visual and audible alerts. On its face, seven LED indicators clearly differentiate between key voltage levels: 24, 120, 208, 240, 277, 480, 600 V AC; and 6, 12, 24, 36, 48,110, 220 V DC.

To increase accuracy and speed, the VPC-10A turns on when a complete circuit is sensed, automatically select AC or DC voltage or continuity mode, and auto-off when removed from a circuit.

Measuring under 6 inches long and weighing less than half a pound, its rugged, compact design allows for easy one-handed use. With an operating battery life of 40 hours and operating temperature ranging from 41 degrees F to 140 degrees F, this tool is just as rugged and reliable as it is safe.

Specifications

Features
LED Voltage range	24…600 VAC, 6…220 V DC
LED voltage indicators	AC volts: 24 V, 120 V, 208 V, 240 V, 277 V, 480 V, 600 V, DC volts: 6 V, 12 V, 24 V, 36 V, 48 V, 110 V, 220 V
Frequency range	50 to 60 Hz
Acoustic indication	≥ 24 VAC, ≥ 6 V DC
Built-in vibration alert	–
Tolerances LEDs	-30% to 0% of reading
Voltage detection	Automatic
Hazardous voltage indication	≥ 24 VAC; ≥ 48 V DC
Range detection	Automatic
Polarity detection	Full range
Continuity indication	LED and buzzer ( 0 to 45 kΩ ON; >85 kΩ OFF)
Continuity range	0 to 45 kΩ
Continuity tolerances	0% to +50%
Continuity buzzer	3 kHz
VolTect™ non-contact voltage	–
Work light	–
Input impedance	1 MΩ
Operating time	30 seconds ON maximum and wait for five minutes before taking another measurement
Operating altitude	≤ 6561 ft (2000 m)
Operating temperature	41 °F to 122 °F (5 °C to 50 °C)
Storage conditions	-22 °F to 140 °F (-30 °C to 60 °C)
Humidity (Without Condensation)	≥ 80% RH at 41 °F to 104 °F (5 °C to 40 °C); ≥ 50% RH at > 104 °F to 122 °F (> 40 °C to 50 °C)
Pollution degree	2
Power supply	Three 1.5 V battery AAA, LR03, UM4 or equivalent
Battery life	40 hours (alkaline) (typical)
Electrical safety	CAN/CSA-C22.2 No. 61010-1-12, UL Std. No. 61010-1 (3rd Edition), CAN/CSA-C22.2 No. 61010-031-07, UL 61010-031 (1st Edition – 2007), CAN/CSA-C22.2 No. 61010-2-030-12, UL 61010-2-030(1st Edition -2012)
Overvoltage category	CAT III 600 V In CAT III environments, use the test probes with the probe caps on.This decreases the exposed probe tip to reduce the possibility of an arc flash from short circuits. When the probe cap is off, the probe tip is 18 mm and rated to CAT II 1000 V.
EMC	Conforms to IEC 61326-1
Dimensions (H x W x D)	5.90 x 2.13 x 1.34 in (150 x 54 x 34 mm)
Weight	Approximately 0.45 lb (205 g) with batteries installed